Alpeg MP615/MP107 Uživatelský manuál

MP615/MP107 MPEG-2 video player User guide WWW.ALPEG.COM

Rev 1.5 Page 9 4.2.3 Example 3 play/clips/pubsony.mpg wait 2 SC01 Goto 1 10 : SC02 Goto 1 This script plays the pubsony.mpg video, waits

Rev 1.5 Page 10 270 5 Appendices 5.1 diagram of DB25 GPI parallel connector wiring (dry contact) 5 channel

Rev 1.5 Page 11 The closing of contact 2 activates an action associated to a command number 2 (example in the file SC00: 2: play /clips/video2.mp

Rev 1.5 Page 12 5.2 Language capacity 5.2.1 sub-scripts. The player allows up to 10 linked sub-scripts to be called up. Example: In th

Rev 1.1 Page 13 6. HTML dialogue pages: 6.1 Main page: Open your Internet explorer and type in the following address of the player: http://10.1

Rev 1.1 Page 14 6.2 Network interface page: 6.2.1 TCP/IP: To communicate with the player for the first time, the following initial steps must

Rev 1.1 Page 15 6.2.2 Programming example so that the player is accessible by the following type of PC address: 192.168.0.10 After having access

Rev 1.1 Page 16 6.2.3 Network interface 2 (factory parameters below) 2) Change the configuration by modifying th

Rev 1.1 Page 17 3) After any modification, remember to SAVE, return to the previous interface to check the new address in the “permanent interfac

Rev 1.1 Page 18 5) Reprogramming the TCP/IP properties of your computer to access the new address, in the current example this could be: IP A

Rev 1.5 Page 1 CONTENTS 2. COMPOSITION 2 3. USAGE 3 3.1 The player 3 3.1.1 Script file 3 3.1.2 Videos

Rev 1.1 Page 19 6.3 Direct TCP/IP reading control page. It is possible to control the Alpeg player by network with the following page:

Rev 1.1 Page 20 6. 4 Main script editor page : Writing the script is done entirely using the mouse intuitively, all you have to do is choose

Rev 1.1 Page 21 Editing page with the SC00 file open.

Rev 1.1 Page 22 6.4.1 Script editing pages: This is in text mode, also called "expert mode". In this ar

Rev 1.1 Page 23 6.4.2 Opening a script in expert mode. There is always, for all players, a default script text file called “SC00”

Rev 1.1 Page 24 The file that has been saved is shown here. 6.4.3 Saving a script file To write a script, please u

Rev 1.1 Page 25 6.5.Player status page (RS232 address) If the player is linked to another player, the number of th

Rev 1.1 Page 26 6.6 Factory preset page : Restore the original TCP/IP configuration; the sound volume will be re

Rev 1.1 Page 27 6.7: MP615 Front panel: Lock key for hard disk Extractible hard disk ON/OFF switch

Rev 1.1 Page 28 6.8 MP107 Front panel: On/off button behind the hatch.

Rev 1.5 Page 2 2. Composition The digital video player is made up of a player section and the following different modules: - A network conne

Rev 1.1 Page 29 6.9 MP107 Rear Panel: General on/off switch Power plug Network connection Dry contact socket RS232 input Not used Audio Stereo Ou

Rev 1.1 Page 30 6.10 MP615 Rear panel: YUV= Blue :2, Red :3, Green :4 RGsB=Blue :2, Red :3, Green :4 2

Rev 1.1 Page 31 RS232 Commands and protocol: Protocol: 9600,n,8,1. Each instruction must be ended with a carriage return. (Odh). You will rec

Rev 1.1 Page 32 Spécifications2: Description Specifications Model number MP 615 Video Compression MP@ML, ISO 13818-2 Accepted MPEG Formats MPE

Rev 1.1 Page 33

Rev 1.5 Page 3 3. Usage 3.1 The player When you turn the player on, the script reader starts up automatically after about 30 seconds. You must

Rev 1.5 Page 4 Introduction to the FTP transfer protocol FTP = File Transfer protocol. After electronic mail and the WEB, FTP is another Inte

Rev 1.5 Page 5 On the contrary, others, before giving you access, ask you to fill out a little form. It's nothing to worry about, and won&a

Rev 1.5 Page 6 3.2.3 RS232 Connection The RS232 connections allow the player to be driven. - See programming chapter - See connection

Rev 1.5 Page 7 4 How to write script(s) 4.1 Language *: equals a space 4.1.1 Play Allows a script to be read Command: Play file_name_mpeg

Rev 1.5 Page 8 4.1.6 R Allows a specific command to be sent to another channel by the series port. There are 3 commands possible: - R*x,